XSP-100 SHARK® Integrated Access Device The XSP 100 Shark let's you deliver voice, high-speed data, Internet access and networking connections to end customers over a single network connection. It's modular design works with emerging technologies. You can change services as needed, making the Shark a "pay-as-you-go" solution that protects your initial investment. The Shark works with a variety of management systems, including HTTP, CLI, SNMP or TL1. It can be configured remotely or through a local craft port on the chassis. Features: Modular design Dual T1s of bandwidth Up to 24 FXS Lines DSX/CSU functionality DHCP and NAT IP address management 10/100 Base T and serial Ethernet interfaces Frame relay Assembler/Disassembler Digital cross connect system Integrated access has reached a new level of simplicity and functionality with the XSP-100 SHARK® Integrated Access Device from Verso / Verilink. The SHARK IAD enables the delivery of voice, highspeed data, and Internet access connections to end customers over a single network connection. Flexible The XSP-100 SHARK IAD was designed to be fully modular resulting in a flexible system that’s easily modified as needs change. Capabilities can be added or removed effortlessly, reducing the potential for a stranded investment. This is truly a “Pay as you go!” platform. Integrated With the capacity for four T1 network interfaces, the XSP-100 SHARK IAD can support up to 6 Mbps of integrated voice and data. In addition to SF and ESF, TR-08 Mode 1 operation is supported, enabling the SHARK IAD to integrate directly with a carrier’s voice switch. The SHARK IAD provides an integrated, easy-to-use 1/0 cross connect that controls the flow of DS0s from the network T1 to customer-side voice or data interfaces. The SHARK IAD will terminate up to 24 analog voice circuits and can also provide digital fractional T1 interfaces for direct connection to a PBX and delivery of data to an external router. Trouble-free The XSP-100 SHARK IAD has a full-featured IP router that provides an SNMP manageable LAN and network interface. The router was designed for easy installation and maintenance through its DHCP and NAT features. Also, the router has an integrated Frame Relay Assembler/Disassembler (FRAD) to handle any Frame Relay traffic from the network and hand it off to the customer via an auto-sensing 10/100Base-T Ethernet connection. The SHARK IAD’s features can be set up easily via one of its many configuration interfaces. Whether you choose the graphic user interface using a Web browser or command line interface using a terminal emulator, the SHARK IAD will fit into your management architecture for provisioning and monitoring. Configuration can be accomplished remotely via telnet or IP, or locally via the craft port on the chassis. Both allow for full access to all of the services and features. DESCRIPTION XSP-100 SHARK® Integrated Access Device WAN PORTS Up to 4 T1 WAN ports T1 line rate – 1.544 Mbps with SF, ESF, and TR-08 framing B8ZS, AMI channel line code Bantam jacks (monitor only) and RJ-48C connector Loop or internal timing via Stratum 4 reference clock User-selectable DS0 assignment VOICE PORTS Three analog voice ports (8 circuits per card) FXS, DPO, E&M Wink, E&M Wink Delay, FXO, and DPT signaling modes Supports CLASS, Loop Start, Ground Start, and Direct Inward Dial 5 REN per card Supports robbed bit signaling DATA PORT (LAN) One 10/100Base-T port (auto-sensing) RJ-45 connector IEEE 802.3 compliant IP ROUTER Protocols supported: TCP/IP, PPP, LCP, UDP, ARP, PAP, CHAP, RIP V1 and V2, ICMP, DHCP, DNS, HTTP DHCP and NAT for IP address management SNMP/Telnet support Transparent Bridging FRAME RELAY ACCESS DEVICE Supports RFC 1490, LMI Q.933 Annex A and LMI ANSI T1.617 Annex D Multiple Permanent Virtual Circuits NETWORK MANAGEMENT Full provision, monitor, and alarm capabilities for each interface Accessable through Web browser Multi-Level Password Protection SNMP Trap Reporting COMMAND LINE INTERFACE Access via RS-232 craft port, Ethernet, FDL, or dedicated DS0 Inband IP, external modem, or Facility Data Link Remote download for software upgrade CHASSIS NEBS Level 3 Certified 3.5” (2U) high x 17.5” wide x 13” deep Mounts on wall, 19” or 23” rack, or desktop Hinges available for swing-out wall mounting POWER -48 VDC 120 VAC with external converter (standard) WARRANTY AND SUPPORT Five-year warranty