Shop

Serial Data Encrypter-0

Serial Data Encrypter

$310.00

In stock

SKU: SE6600-R Category:

Description

DESCRIPTION

The SE-6600R is an industrial rated serial data encryption device featuring two serial ports, a device port and a network port. The SE-6600R uses AES 256-bit encryption, 128-bit block size. AES is the US Government standard encryption algorithm approved for FIPS and AGA purposes.

The SE-6600R provides a secure link between host and remote user sites. The two RS232 serial ports operate at asynchronous speeds as low as 1200 bps and as high as 57.6 Kbps. The SE-6600R serial interface can be RS232, RS422, or RS485 2-wire or 4-wire.

The SE-6600R may be used point-to-point, linking two separate remote sites with radios, leased lines or dial connections, one port used for the connection, the other port for the user equipment. The SE-6600R can also be used on point-to-multipoint links. The SE-6600R is especially attractive for use over multipoint radios where high security is desired.

The SE-6600R has a bypass mode (Block Mode Clear) for use during initial installation. When installing in a large multidrop network, it is desirable to have the remote units not encrypt data until the host unit is installed. This makes the scheduling of installation less critical, as the initial remote installation will not disable the drop if a host unit is not yet in service. The remote unit is temporarily just a bump in the serial cable.

The SE-6600R is straight-forward, easy to configure and maintain. Units are configured via a terminal connection to the serial port, or using the Ethernet port, via telnet or a web browser. The SE-6600R has the features you want without the complexity.

The nature of the encryption protocols used in the product make it suitable for polling or packetized data only. For streaming data, please see the SSE-R, Streaming Serial Encrypter product.

Due to the encryption employed, SE-6600R product is an export controlled item and is regulated by the Bureau of Industry and Security (BIS) of the U.S. Department of Commerce. The SE-6600R is classified as mass market encryption device and may not be exported or shipped for re-export to restricted countries in Country Group E:1. They are readily shippable to most other countries.



SPECIFICATIONS

General

  • Two asynchronous serial ports: configurable for RS232, RS422/RS485 4-wire
  • DE-9P (PC-9 pin) connectors, DTE interface
  • Speeds to 57.6 Kbps, full or half duplex
  • Can be configured via RS232 serial port
  • Ethernet port for telnet or web browser management
  • Delivered with RS232 9-pin to 9-pin adapters and cable for setup or connection to PCs or other devices with 9-pin DTE interfaces

Protocol Features

  • 256 bit AES encryption
  • Block Cipher – CipherFeedback Mode
  • Transmit on idle time, fixed time period, block size, or character
  • Due to the nature of the encryption protocols used in the product, it is sppropriate for polling or packetized data only. For streaming data, please see SSE-R, Streaming Serial Encrypter product
  • Compatible with older SE-6600 hardware
  • If dial-up modems are used, the modems must be able to dial and connect by themselves.  There is no provision for the SE-6600R to issue or passthrough a dial command to the modem.

Indicators

  • LAN status, DCD, Run/Power, Encrypting, Tx Data on Com 1 & 2

Controls

  • Switch to invoke serial port setup

Physical/Electrical

  • Power Requirements: 9 to 30 VDC, (2 watts) standard
  • 48, 125 VDC and 240 VAC options are available
  • Supplied with 120 VAC to 9 VDC external power supply
  • Dimensions: 4 1/4” x 3” x 1”
  • Weight: 7.5 oz.
  • DIN rail mounting clip available

Environmental

  • Operational Temperature: – 40 to +75 C, 95% non-condensing humidity
SE-6600R Polling Data Serial Encrypter (5-30VDC and 120 VAC power supply)
9501033 Optional 36-72 VDC Input Power Supply
9501081 Optional 125 VDC Input Power Supply
9902090 Optional DIN rail mounting clips

Additional information

Weight 2 lbs
Dimensions 5 × 5 × 5 in